Motorized Shades Blinds Manufacturers Introduces How To Properly Debug The Remote Control Of The Curtain Motor
2022-4-18
Motorized Shades Blinds Manufacturers introduces how to debug the remote control of electric curtain motors?
1. Remote control mode
Press the lift or stop key, the remote control mode indicator light is on, press the "infrared and radio mode conversion key" to switch to the desired mode.
2. Channel clear
Please turn off the power for 15 seconds and then turn on the power. After hearing a short beep from the motor, enter the setting state. Press and hold the "stop button" and "channel learning button" at the same time within 20 seconds, and hear the motor from short beep to long beep. , release the two keys, all the channels previously set by the motor will be cleared. Saishang shading editor, if the sunshade net does not add the original link of Saishang, the behavior is shameful!
3. Channel setting
Press the "channel selection key" to the desired channel (the channel indicator light is on), in the motor setting state, press the learning key, hear the long beep of the motor, and the channel learning is completed. Within 20 seconds, select another channel or another remote control channel, and operate in sequence to set 30 channels or the remote control to operate one motor.
4. Motor commutation
Before setting the stroke, check whether the up and down stroke direction of the motor is consistent with the direction of the up and down buttons on the remote control. Press and hold the "up button" and "down button" at the same time, and when the motor changes from a short beep to a long beep, release the two buttons. After the direction change is completed, the originally set travel position is canceled.
5. the setting of the up and down stroke position
In the motor setting state, press and hold the "set key" for 5 seconds. After the motor changes from a short beep to a long beep, it enters the stroke setting state. Press the "up button" to rise to the required upper limit position, press the "stop button" to stop, first press and hold the "stop button", then press and hold the "up button", after hearing the long beep of the motor, release the Open the two buttons to set the upper limit position of the stroke; Similarly, press the "down key" to drop to the required lower limit position, press the "stop key" to stop, first hold down the "stop key", then press and hold down the "down key", and hear a long beep of the motor After that, release the two buttons to set the lower limit position of the stroke.
Through the above introduction, Dc Solar Motor For Roller Shutter Manufacturers hopes that you can simply refer to the content of this article in future use.
2022-4-18
Motorized Shades Blinds Manufacturers introduces how to debug the remote control of electric curtain motors?
1. Remote control mode
Press the lift or stop key, the remote control mode indicator light is on, press the "infrared and radio mode conversion key" to switch to the desired mode.
2. Channel clear
Please turn off the power for 15 seconds and then turn on the power. After hearing a short beep from the motor, enter the setting state. Press and hold the "stop button" and "channel learning button" at the same time within 20 seconds, and hear the motor from short beep to long beep. , release the two keys, all the channels previously set by the motor will be cleared. Saishang shading editor, if the sunshade net does not add the original link of Saishang, the behavior is shameful!
3. Channel setting
Press the "channel selection key" to the desired channel (the channel indicator light is on), in the motor setting state, press the learning key, hear the long beep of the motor, and the channel learning is completed. Within 20 seconds, select another channel or another remote control channel, and operate in sequence to set 30 channels or the remote control to operate one motor.
4. Motor commutation
Before setting the stroke, check whether the up and down stroke direction of the motor is consistent with the direction of the up and down buttons on the remote control. Press and hold the "up button" and "down button" at the same time, and when the motor changes from a short beep to a long beep, release the two buttons. After the direction change is completed, the originally set travel position is canceled.
5. the setting of the up and down stroke position
In the motor setting state, press and hold the "set key" for 5 seconds. After the motor changes from a short beep to a long beep, it enters the stroke setting state. Press the "up button" to rise to the required upper limit position, press the "stop button" to stop, first press and hold the "stop button", then press and hold the "up button", after hearing the long beep of the motor, release the Open the two buttons to set the upper limit position of the stroke; Similarly, press the "down key" to drop to the required lower limit position, press the "stop key" to stop, first hold down the "stop key", then press and hold down the "down key", and hear a long beep of the motor After that, release the two buttons to set the lower limit position of the stroke.
Through the above introduction, Dc Solar Motor For Roller Shutter Manufacturers hopes that you can simply refer to the content of this article in future use.
Motorized Shades Blinds Manufacturers Introduces How To Properly Debug The Remote Control Of The Curtain Motor
2022-4-18
Motorized Shades Blinds Manufacturers introduces how to debug the remote control of electric curtain motors?
1. Remote control mode
Press the lift or stop key, the remote control mode indicator light is on, press the "infrared and radio mode conversion key" to switch to the desired mode.
2. Channel clear
Please turn off the power for 15 seconds and then turn on the power. After hearing a short beep from the motor, enter the setting state. Press and hold the "stop button" and "channel learning button" at the same time within 20 seconds, and hear the motor from short beep to long beep. , release the two keys, all the channels previously set by the motor will be cleared. Saishang shading editor, if the sunshade net does not add the original link of Saishang, the behavior is shameful!
3. Channel setting
Press the "channel selection key" to the desired channel (the channel indicator light is on), in the motor setting state, press the learning key, hear the long beep of the motor, and the channel learning is completed. Within 20 seconds, select another channel or another remote control channel, and operate in sequence to set 30 channels or the remote control to operate one motor.
4. Motor commutation
Before setting the stroke, check whether the up and down stroke direction of the motor is consistent with the direction of the up and down buttons on the remote control. Press and hold the "up button" and "down button" at the same time, and when the motor changes from a short beep to a long beep, release the two buttons. After the direction change is completed, the originally set travel position is canceled.
5. the setting of the up and down stroke position
In the motor setting state, press and hold the "set key" for 5 seconds. After the motor changes from a short beep to a long beep, it enters the stroke setting state. Press the "up button" to rise to the required upper limit position, press the "stop button" to stop, first press and hold the "stop button", then press and hold the "up button", after hearing the long beep of the motor, release the Open the two buttons to set the upper limit position of the stroke; Similarly, press the "down key" to drop to the required lower limit position, press the "stop key" to stop, first hold down the "stop key", then press and hold down the "down key", and hear a long beep of the motor After that, release the two buttons to set the lower limit position of the stroke.
Through the above introduction, Dc Solar Motor For Roller Shutter Manufacturers hopes that you can simply refer to the content of this article in future use.
0 Comments
0 Shares